Softub Replacement Pumps with Pre-Installed Thermal Wrap
Softub Systems Include:
Motor & Pump with Pre-Installed Thermal Wrap Heat Jacket
Motor:
Mfg: Century
HP: 1 - Service factor 1.0 (1.5hp SPL/Up-rated)
RPM: 3450
Single Speed
Volts: 115
Amps: 13.6
HZ: 60
Frame: 56Z (48Y)
Thermally Protected
Softub Original Pump / Wet End: (pre-installed on motor)
Manufactured by Vico/Balboa for Softub
1 HP (1.5HP SPL)
1 1/2" Industry and Softub Standard Connections
(threads measure 2 3/8" across)
Thermal Wrap Heat Jacket: Pre-installed on motor
(top port on Thermal Wrap is plugged and not used for Softub applications)
32" - 3/8" ID Tubing & 4 Tubing Clamps: (Included with Model: CSCD) for making tubing connections between the 2 ports on Thermal Wrap and the in and out ports in existing plumbing
Feel free to give us a call and discuss your needs.
For Free Technical Support - Call Jim - 832-722-8412
We are the manufacture of the Genuine Heat Recycling System
Designed for Spas - Hot Tubs and Whirlpool Bathtubs
Model: BSFD
Connect new motor using your existing pump cord
(pump cord not supplied)
Models: CSCD & CSSD
Available in Three Standard Models / Configurations:
Model: CSCD (Center Suction x Center Discharge)
Model: BSFD (Bottom Suction x Front Discharge)
Model: CSSD (Center Suction x Side Discharge)
Custom Configurations available.
Complete Pump & Motor with Pre-installed Thermal Wrap
1 1/2" - Fits your existing Softub pump unions
$248.00
$257.00
Complete Pump & Motor with Pre-instralled Thermal Wrap
2 1/4" Slip on hose connections
This patented heating system is designed to replace your existing Softub coil wrapped motor and pump. The Thermal Wrap - Heat Recycling System captures and recycles the waste heat "energy" produced by the pump/motor and delivers that heat to the tub water just like the Softub pump.
Through the past 20+ years we have supplied hundreds of Thermal Wrap Heat Recycling system for Softub applications. We have also supplied more than 30,000 Thermal Wrap systems for spas other than the Softub brand.
Tub water circulates through a serpentine path in the Thermal Wrap, collecting the heat generated by the pump/motor and recycles that heat to the tub water.
(Wet Ends ship pre-assembled for easy installation)
Model: WE-BSFD - Wet End
(Bottom Suction x Front Discharge)
Complete Pump/Wet End with Impeller & Seal
1HP (1 1/2 SPL/Uprated)
Slip On Connections
$74.00
Model: WE-CSCD - Wet End
(Center Suction x Center Discharge)
Complete Pump/Wet End with Impeller & Seal
1HP (1 1/2 SPL/Uprated)
1 1/2" Threaded Connections
$68.00
(Center Suction x Side Discharge)
Complete Pump/Wet End with Impeller & Seal
1HP (1 1/2 SPL/Uprated)
1 1/2' Threaded Connections
$68.00
1 1/2" Buttress x 1 1/2" Slip x 3/8" Barb with O-rings
$16.00
1 1/2" Buttress x 1 1/2" Slip - No Barbs
Fits suction and discharge threaded pump connections for 1 1/2" sch. 40 rigid & flexible PVC pipe:
$8.98
1 1/2" Slip x 1 1/2" Slip
with Duel Thermowells
Complete Pump & Motor with Pre-installed Thermal Wrap
1 1/2" - Fits your existing Softub pump unions
$248.00
Efficient...
● Thoroughly tested with a proven track record
● Patented design, over 1,000,000 in use.
● Special thermal conductive inner heat transfer liner.
● Models available for most Spa/Hot Tub & Jetted Tub Pumps
Economical...
●
Maintenance free - no moving parts to wear out
● Helps keep motor cooler increases motor longevity and efficiency
● Cost less than electric heaters
Safe...
● Manufactured of non-conductive materials
● Non electrical
Model: Aqua-Flo WE-CSCD - Wet End
(Center Suction x Center Discharge)
Complete Pump/Wet End with Impeller & Seal
1HP (1 1/2 SPL/Uprated)
1 1/2" Threaded Connections
$74.00